Проблемы с загрузкой

Имеется сервер HP Proliant DL 145

Загрузился с Лив СД для AMD64

Скомпилил ядро через genkernel all (потом подправил кое какие прараметры через menuconfig)

Установил grub

в конфиге grub.conf написал

default 0
timeout 30
splashimage=(hd0,0)/grub/splash.xpm.gz

title=Gentoo Linux 2.6.17-r8
root (hd0,0)
kernel /kernel-genkernel-x86_64-2.6.17-gentoo-r8 root=/dev/sda1 init=/linuxrc ramdisk=8192 real_root=/d
ev/sda3 udev
initrd /initramfs-genkernel-x86_64-2.6.17-gentoo-r8

После загрузки уже с винта возникает следующая ошибка

>> Determining root device
!! block device /dev/sda3 not a valid root device...
!! the root block device is not specified or not detected...
please specify a device to boot, or "shell" for a shell....
bott() ::

в чем может быть проблема?

Все что связаное с файловыми системами вкомпилил в ядро.

Вот мой dmesg c LiveDC

Bootdata ok (command line is root=/dev/ram0 init=/linuxrc dokeymap looptype=squashfs loop=/image.squash
fs cdroot initrd=gentoo.igz vga=791 splash=silent,theme:livecd-2006.1 CONSOLE=/dev/tty1 quiet BOOT_IMAG
E=gentoo )
Linux version 2.6.17-gentoo-r7 (root@poseidon) (gcc version 4.1.1 (Gentoo 4.1.1)) #1 SMP Tue Aug 29 01:
41:38 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003ffff000 (ACPI data)
BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
DMI 2.3 present.
ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000f44b0
ACPI: XSDT (v001 HP OEMXSDT 0x03000407 MSFT 0x00000097) @ 0x000000003fff0100
ACPI: FADT (v003 HP OEMFACP 0x03000407 MSFT 0x00000097) @ 0x000000003fff0281
ACPI: MADT (v001 HP OEMAPIC 0x03000407 MSFT 0x00000097) @ 0x000000003fff0380
ACPI: OEMB (v001 HP OEMBIOS 0x03000407 MSFT 0x00000097) @ 0x000000003ffff040
ACPI: SRAT (v001 HP OEMSRAT 0x03000407 MSFT 0x00000097) @ 0x000000003fff2d20
ACPI: ASF! (v016 AMIASF AMDSTRET 0x00000001 INTL 0x02002026) @ 0x000000003fff2e10
ACPI: DSDT (v001 HP 0ABFD08a 0x00000001 INTL 0x02002026) @ 0x0000000000000000
On node 0 totalpages: 257449
DMA zone: 2944 pages, LIFO batch:0
DMA32 zone: 254505 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x5008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:5 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:5 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfebfe000] gsi_base[24])
IOAPIC[1]: apic_id 3, version 17, address 0xfebfe000, GSI 24-27
ACPI: IOAPIC (id[0x04] address[0xfebff000] gsi_base[28])
IOAPIC[2]: apic_id 4, version 17, address 0xfebff000, GSI 28-31
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bf7c0000)
Checking aperture...
CPU 0: aperture @ 7b4c000000 size 32 MB
Aperture from northbridge cpu 0 too small (32 MB)
No AGP bridge found
Built 1 zonelists
Kernel command line: root=/dev/ram0 init=/linuxrc dokeymap looptype=squashfs loop=/image.squashfs cdroo
t initrd=gentoo.igz vga=791 splash=silent,theme:livecd-2006.1 CONSOLE=/dev/tty1 quiet BOOT_IMAGE=gentoo

Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Disabling vsyscall due to use of PM timer
time.c: Using 3.579545 MHz WALL PM GTOD PM timer.
time.c: Detected 1592.995 MHz processor.
Speakup v-2.00 CVS: Mon May 1 09:46:33 EDT 2006 : initialized
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 1023208k/1048512k available (2561k kernel code, 24560k reserved, 802k data, 180k init)
Calibrating delay using timer specific routine.. 3188.44 BogoMIPS (lpj=1594223)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
Using local APIC timer interrupts.
result 12445288
Detected 12.445 MHz APIC timer.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3185.58 BogoMIPS (lpj=1592794)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
AMD Opteron(tm) Processor 242 stepping 08
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff -63 cycles, maxerr 911 cycles)
Brought up 2 CPUs
testing NMI watchdog ... OK.
migration_cost=694
checking if image is initramfs... it is
Freeing initrd memory: 4556k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:04.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI-DMA: Disabling IOMMU.
pnp: 00:07: ioport range 0x680-0x6ff has been reserved
pnp: 00:07: ioport range 0x295-0x296 has been reserved
pnp: 00:0a: ioport range 0xca2-0xca3 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: c000-cfff
MEM window: fe200000-feafffff
PREFETCH window: ff500000-ff5fffff
PCI: Bridge: 0000:00:02.0
IO window: disabled.
MEM window: fe100000-fe1fffff
PREFETCH window: ff400000-ff4fffff
PCI: Bridge: 0000:00:06.0
IO window: b000-bfff
MEM window: fc000000-fe0fffff
PREFETCH window: ff300000-ff3fffff
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
squashfs: version 3.0 (2006/03/15) Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered (default)
PCI: MSI quirk detected. PCI_BUS_FLAGS_NO_MSI set for subordinate bus.
PCI: MSI quirk detected. PCI_BUS_FLAGS_NO_MSI set for subordinate bus.
Real Time Clock Driver v1.12ac
initialized device: /dev/synth, node ( MAJOR 10, MINOR 25 )
Linux agpgart interface v0.101 (c) Dave Jones
vesafb: framebuffer at 0xfd000000, mapped to 0xffffc20000080000, using 3072k, total 8128k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AMD8111: IDE controller at PCI slot 0000:00:07.1
AMD8111: chipset revision 3
AMD8111: not 100% native mode: will probe irqs later
AMD8111: 0000:00:07.1 (rev 03) UDMA100 controller
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:DMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard as /class/input/input0
logips2pp: Detected unknown logitech mouse model 0
input: ImPS/2 Logitech Wheel Mouse as /class/input/input1
hdb: CD-W524E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hdb: ATAPI 40X CD-ROM CD-R/RW drive, 1404kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 180k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:01:00.0[D] -> GSI 19 (level, low) -> IRQ 16
ohci_hcd 0000:01:00.0: OHCI Host Controller
ohci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:01:00.0: irq 16, io mem 0xfe0fd000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:01:00.1[D] -> GSI 19 (level, low) -> IRQ 16
ohci_hcd 0000:01:00.1: OHCI Host Controller
ohci_hcd 0000:01:00.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:01:00.1: irq 16, io mem 0xfe0fe000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
sl811: driver sl811-hcd, 19 May 2005
ieee1394: Initialized config rom entry `ip1394'
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
libata version 1.20 loaded.
device-mapper: 4.6.0-ioctl (2006-02-17) initialised:

JFS: nTxBlock = 8033, nTxLock = 64269
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
tg3.c:v3.59 (June 8, 2006)
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 31 (level, low) -> IRQ 17
eth0: Tigon3 [partno(BCM95704) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:00
:1a:19:42:a9
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[769f4000] dma_mask[64-bit]
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI Interrupt 0000:02:03.1[B] -> GSI 28 (level, low) -> IRQ 18
eth1: Tigon3 [partno(BCM95704) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:00
:1a:19:42:a8
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth1: dma_rwctrl[769f4000] dma_mask[64-bit]
tg3.c:v3.59 (June 8, 2006)
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 31 (level, low) -> IRQ 17
eth0: Tigon3 [partno(BCM95704) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:00
:1a:19:42:a9
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[769f4000] dma_mask[64-bit]
ACPI: PCI Interrupt 0000:02:03.1[B] -> GSI 28 (level, low) -> IRQ 18
eth1: Tigon3 [partno(BCM95704) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:00
:1a:19:42:a8
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth1: dma_rwctrl[769f4000] dma_mask[64-bit]
Fusion MPT base driver 3.03.09
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT SPI Host driver 3.03.09
GSI 19 sharing vector 0xC1 and IRQ 19
ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 25 (level, low) -> IRQ 19
mptbase: Initiating ioc0 bringup
ioc0: 53C1030: Capabilities={Initiator}
scsi0 : ioc0: LSI53C1030, FwRev=01030f00h, Ports=1, MaxQ=222, IRQ=19
mptbase: ioc0: RAID STATUS CHANGE for VolumeID 0
mptbase: ioc0: volume is now degraded, enabled
Vendor: LSILOGIC Model: 1030 IM Rev: 1000
Type: Direct-Access ANSI SCSI revision: 02
mptbase: ioc0: RAID STATUS CHANGE for VolumeID 0
mptbase: ioc0: volume is now degraded, enabled, resync in progress
SCSI device sda: 71020545 512-byte hdwr sectors (36363 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 08
SCSI device sda: drive cache: write back
SCSI device sda: 71020545 512-byte hdwr sectors (36363 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 08
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
Vendor: COMPAQ Model: BD03695A27 Rev: HPB6
Type: Direct-Access ANSI SCSI revision: 03
mptbase: ioc0: RAID STATUS CHANGE for VolumeID 0
mptbase: ioc0: volume is now degraded, enabled, quiesced, resync in progress
mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 0
mptbase: ioc0: PhysDisk is now online, quiesced
mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 1
mptbase: ioc0: PhysDisk is now online, out of sync, quiesced
target0:1:0: Beginning Domain Validation
target0:1:0: Ending Domain Validation
mptbase: ioc0: RAID STATUS CHANGE for VolumeID 0
mptbase: ioc0: volume is now degraded, enabled, resync in progress
mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 0
mptbase: ioc0: PhysDisk is now online
mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 1
mptbase: ioc0: PhysDisk is now online, out of sync
target0:1:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI WRFLOW PCOMP (6.25 ns, offset 63)
Vendor: COMPAQ Model: BD03695A27 Rev: HPB6
Type: Direct-Access ANSI SCSI revision: 03
mptbase: ioc0: RAID STATUS CHANGE for VolumeID 0
mptbase: ioc0: volume is now degraded, enabled, quiesced, resync in progress
mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 0
mptbase: ioc0: PhysDisk is now online, quiesced
mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 1
mptbase: ioc0: PhysDisk is now online, out of sync, quiesced
target0:1:8: Beginning Domain Validation
target0:1:8: Ending Domain Validation
mptbase: ioc0: RAID STATUS CHANGE for VolumeID 0
mptbase: ioc0: volume is now degraded, enabled, resync in progress
mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 0
mptbase: ioc0: PhysDisk is now online
mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 1
mptbase: ioc0: PhysDisk is now online, out of sync
target0:1:8: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI WRFLOW PCOMP (6.25 ns, offset 63)
input: PC Speaker as /class/input/input2
PM: Writing back config space on device 0000:02:03.0 at offset b (was 164814e4, writing 36c01022)
PM: Writing back config space on device 0000:02:03.0 at offset 3 (was 804000, writing 804010)
PM: Writing back config space on device 0000:02:03.0 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:02:03.0 at offset 1 (was 2b00000, writing 2b00146)
fbsplash: console 0 using theme 'livecd-2006.1'
fbsplash: switched splash state to 'on' on console 0
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
PM: Writing back config space on device 0000:02:03.0 at offset b (was 164814e4, writing 36c01022)
PM: Writing back config space on device 0000:02:03.0 at offset 3 (was 804000, writing 804010)
PM: Writing back config space on device 0000:02:03.0 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:02:03.0 at offset 1 (was 2b00000, writing 2b00146)
PM: Writing back config space on device 0000:02:03.0 at offset b (was 164814e4, writing 36c01022)
PM: Writing back config space on device 0000:02:03.0 at offset 3 (was 804000, writing 804010)
PM: Writing back config space on device 0000:02:03.0 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:02:03.0 at offset 1 (was 2b00000, writing 2b00146)
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.

Вот мой fstab

#

# NOTE: If your BOOT partition is ReiserFS, add the notail option to opts.
/dev/sda1 /boot ext2 noauto,noatime 1 2
/dev/sda3 / ext3 noatime 0 1
/dev/sda2 none swap sw 0 0
/dev/cdroms/cdrom0 /mnt/cdrom iso9660 noauto,ro 0 0
#/dev/fd0 /mnt/floppy auto noauto 0 0

# NOTE: The next line is critical for boot!
proc /proc proc defaults 0 0

# glibc 2.2 and above expects tmpfs to be mounted at /dev/shm for
# POSIX shared memory (shm_open, shm_unlink).
# (tmpfs is a dynamically expandable/shrinkable ramdisk, and will
# use almost no memory if not populated with files)
shm /dev/shm tmpfs nodev,nosuid,noexec 0 0

livecd ~ # lsmod
Module Size Used by
ipv6 219744 16
pcspkr 6144 0
mptspi 16656 2
mptscsih 19456 1 mptspi
mptbase 43616 2 mptspi,mptscsih
scsi_transport_spi 20736 1 mptspi
tg3 92420 0
nfs 89808 0
lockd 50448 1 nfs
sunrpc 116936 2 nfs,lockd
jfs 142032 0
dm_mirror 18560 0
dm_mod 42320 1 dm_mirror
pdc_adma 11140 0
sata_mv 18696 0
ata_piix 13188 0
ahci 15748 0
sata_qstor 11396 0
sata_vsc 10244 0
sata_uli 9476 0
sata_sis 9860 0
sata_sx4 14596 0
sata_nv 11012 0
sata_via 10500 0
sata_svw 9732 0
sata_sil24 12804 0
sata_sil 11528 0
sata_promise 13060 0
libata 48152 15 pdc_adma,sata_mv,ata_piix,ahci,sata_qstor,sata_vsc,sata_uli,sata_sis,sata_sx4,sata_nv,sata_via,sata_svw,sata_sil24,sata_sil,sata_promise
sbp2 22280 0
ohci1394 31048 0
ieee1394 66296 2 sbp2,ohci1394
sl811_hcd 14080 0
ohci_hcd 19844 0
uhci_hcd 22032 0
usb_storage 66112 0
usbhid 35488 0
ehci_hcd 27912 0
usbcore 96800 7 sl811_hcd,ohci_hcd,uhci_hcd,usb_storage,usbhid,ehci_hcd

livecd ~ # lspci
00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12)
00:01.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01)
00:02.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12)
00:02.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X IOAPIC (rev 01)
00:06.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8111 PCI (rev 07)
00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-8111 LPC (rev 05)
00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev 03)
00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-8111 ACPI (rev 05)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
01:00.1 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
01:04.0 VGA compatible controller: ATI Technologies Inc Rage XL AGP 2X (rev 27)
02:03.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 03)
02:03.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 03)
03:01.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07)

livecd ~ # mount
tmpfs on / type tmpfs (rw)
/dev/hdb on /mnt/cdrom type iso9660 (ro)
/dev/loop0 on /mnt/livecd type squashfs (ro)
proc on /proc type proc (rw)
sysfs on /sys type sysfs (rw)
udev on /dev type tmpfs (rw,nosuid)
devpts on /dev/pts type devpts (rw)
cachedir on /mnt/livecd/lib64/splash/cache type tmpfs (rw)
tmpfs on /mnt/livecd/lib64/splash/tmp type tmpfs (rw)
tmpfs on /mnt/livecd/lib64 type tmpfs (rw)
tmpfs on /mnt/livecd/usr/portage type tmpfs (rw)
usbfs on /proc/bus/usb type usbfs (rw,devmode=0664,devgid=85)
/dev/sda3 on /mnt/gentoo type ext3 (rw)
/dev/sda1 on /mnt/gentoo/boot type ext2 (rw)
proc on /mnt/gentoo/proc type proc (rw)

В чем может быть проблема? Может быть для рейда надо в грубе указывать еще какието дополнительные параметры?